The first design difference is how I constructed the sides and legs. I made this change because it is simpler and sleeker. I made the top two drawers slightly shorter and each drawer width 1/4" smaller so you would only need one sheet of 3/4"plywood making it much less expensive! The remaining design and construction methods are the same as my dresser - consider this the new and improved version! The Purebond really made this dresser pretty!
(This is a mod of Patrick's Beach Dresser from anawhite.com - thanks!)
Link to these plans on ana-white.com
***special note*** If you do not have a jigsaw or if you are planning to stain the dresser, there is a modification for each instance in step 4. Each of these requires the purchase of an additional 1x2x6.
4 - 1x2x8
1 - 1x2x6
2 - 1x3x6
1 - 1x5x6
3 - 1x8x8
1 sheet 3/4" birch plywood
1 sheet 1/2" birch plywood
2 sheets 1/4" birch plywood (review cut list below before purchasing)
8 pair 14" euro drawer slides
2" finish nails
1 1/4" finish nails
5/8" finish nails
1 1/4" pocket hole screws
hammer or nailer
compound miter saw
CUT LIST - Boards
4 - 1x2 @14 1/4"
4 - 2x2 @35 1/4"
2 - 2x2 @ 62 1/4"
1 - 1x2 @ 62 1/4"
6 - 1x2 @ 30 3/4"
Small drawer fronts:
2 - 1x5 @ 30 1/2"
Large drawer fronts:
6 - 1x8 @ 30 1/2"
1 - 1x2 @ 67 1/4"
2 - 1x2 @ 18 1/4"
CUT LIST - Plywood
2 - 14 1/4" x 32 1/2"
1 - 17 1/4" x 31 3/4"
Top and bottom:
2 - 15 3/4" x 62 1/4"
Large drawer front/backs:
12 - 5 3/4" x 28 3/4"
Small drawer front/backs:
4 - 3 1/2" x 28 3/4"
Large drawer sides:
12 - 5 3/4" x 14"
Small drawer sides:
4 - 3 1/2" x 14"
8 - 14" x 29 3/4"
1 - 32 1/2" x 65 1/4"
PLEASE read through the directions entirely before starting this project. Please use eye and hearing protection as well as any recommended safety features on your equipment.
Step 1. Predrill 4 pocket holes in the inside top of each side to use later to attach the dresser top. Attach trim to sides with glue and either 1 1/4" finish nails or screws from the inside. The plywood has a 'good' and a 'not so good' side, so make sure you face the good side out.
Step 2. Attach the posts to each side with pocket holes and 1 1/4" screws keeping the tops flush.
Step 3. Attach the dresser bottom to the sides keeping the back of the dresser bottom flush with the back legs. There should be a 1 1/2" space at the front. Lay the pieces on the ground like the dresser is on its back. Making sure each corner is square, attach using pocket holes and 1 1/4" screws from underneath.
Step 4: Using a jigsaw, cut inserts in center section as shown below. In addition to drawing the lines, you may want to use a straight edge to keep these corners square.
If you don't have a jigsaw, make the center dimenstions as shown below and attach 1x2s as shown. The extra 1x2 cut will be 1@ 29 1/2" and 1 @ 31". Use pocket hole screws to screw from the center section into the 1x2s. Try to place these where the center of the drawers will be to avoid interfering with the drawer divider or drawer slide placement.
***staining the dresser***
If you want to stain the dresser, this option will let you avoid sanding the plywood edge to accommodate edge banding and will also keep all the front trim the same type of wood taking the stain more evenly. The extra 1x2 cut will be 1@ 29 1/2". Use pocket hole screws to screw from the center section into the 1x2. Try to place these where the center of the drawers will be to avoid interfering with the drawer divider or drawer slide placement.
Step 5: With the dresser still on its back, attach the center section using plenty of glue and screw from underneath. Use 5 1 1/4" screws.
Step 6. Attach front trim pieces (2x2s) using the cutouts as guides. For the bottom trim, glue and use 2" finish nails or pocket holes from underneath. Screw directly from underneath into the cutout using 2 1/4" screws.
For the top trim, attach with 2 pocket holes on each side underneath and screw directly from the top into the center cutout using 2 1/4" screws. (I also used glue on each cutout.)
Step 7. Attach the 1x2 brace to the back with pocket holes under each side and screwing directly into the cutout using 1 1/4" screws.
Step 8: Drill 2 pocket holes into each end of the drawer dividers. With the holes facing downward, attach to the center and sides. Cut a piece of wood 7 1/2" and one 4 3/4" to use as a guide/jig for each opening. It is very important that each opening is square.
Step 9: Build drawer boxes as shown. There should be 6 larger and 2 smaller. Check for square. Put your pocket holes in the front and the very back. The drawer fronts will cover the front pocket holes, and you won't ever see the back holes.
Step 10: Add drawer bottoms using glue and 5/8" finish nails.
Step 12: Attach trim to top using glue and pocket holes from underneath or 2" finish nails. (If you don't want to miter the corners, cut the 2 side pieces to 15 3/4" and do a butt joint with the unmitered 67 1/4" front trim piece.
Step 13. Place dresser top upside down on the ground. Remove drawers, and place dress upside down so that the backs of the dresser and dresser top are flush and there is a 1" overhang on the front and sides. Attach using the pocket holes and 1 1/4" screws. Also, screw through the brace into the top using 1 1/4" screws.
Step 14. Using glue and 5/8" finish nails, attach back to dresser.
*This post was written before I changed the name of my blog.*